Marking a new era for Sports Utility Vehicles, the 2002 Ford Explorer remains better for rough terrains and off-road usage. Nevertheless, the 2002 Ford Explorer shown that SUVs can be handy for daily purposes, while possessing some fantastic features, including a 5-speed automatic transmission which turned out to be not so durable. The Transmission used on the 2002 Ford Explorer still had some Common Transmission Problems.
2002 Ford Explorer Transmission Models
The 2002 Ford Explorer comes in two variants. The first variant was a 4.6-liter V-type featuring eight cylinders while the second variant occurs in a 4.0-liter V-6. Both models are made available in either a 5-speed automatic or manual transmission. The Ford Explorer presently uses:
These Transmission models come in both 2 and 4-wheel drive Explorers. Nonetheless, they are not without problems.
2002 Ford Explorer Transmission Problems
Below are the most common 2002 Ford Explorer Transmission Problems.
Failed Solenoid Symptoms on 2002 Ford Explorer
Failure in solenoid is amongst the most common 2002 Ford Explorer transmission problems. The solenoids are in charge of controlling several functions inside the transmission. These small plungers like devices are controlled by your vehicle’s computer to change gears and route pressurized transmission fluid. The processor activates the solenoids through electrical charge sent through a wire coil wrapped around the plunger tool.
Heat and vibration cause short out in these wires, which lead to a variety of transmission problems. After a few thousand miles, the 2002 Ford Explorer starts by displaying problems with its solenoids (5R55W only).
Solenoids failure includes symptoms of no gears shifting and improper function of the torque converter.
How to Fix Solenoid Problems on 2002 Ford Explorer
To check your solenoids functionality, use an ohmmeter connected to the two wires from the solenoid. Readings of 20-30 ohms indicate proper functioning. Anything less or above may lead to your solenoid not to function correctly. Replacement of solenoid is not costly but can turn out to be dangerous if it fails while driving. If you experience any terrible transmission symptoms or solenoid Failure with your 5R55W model transmission, it is best to contact your local mechanic quickly to perform transmission troubleshooting before the problem worsens.
Flashing Overdrive Light
Another common problem linked with the 2002 Ford Explorer transmission problems or the 5R55W transmission is the Flashing Overdrive Light. The bad transmission symptoms of this problem include giving an error code directed at solenoid failure.
How to Fix: Replacing the solenoid was reported to solve the transmission locking up. In such scenarios, rebuilding the transmission becomes necessary.
Harsh Gear Shifting
Harsh gear shifting is also another transmission problem found in the 2002 Ford Explorer and the 5R55W transmission. The bad transmission symptoms associated with this problem include shudder and vibration while accelerating or when the gears shift down. Some 2002 Ford Explorer models may experience slipping between the 2-3 shift or a complete loss of the 3rd gear. This transmission problem is more likely caused by a broken intermediate band, which may trigger P0733 and P0745 diagnostic trouble codes.
How to Fix: Fixing this problem requires replacing both intermediate and OD bands, alongside the pistons. When performing the transmission troubleshooting, the direct clutch drum should be checked for damages as well.
Another known 2002 Ford Explorer transmission problems are overheating. The bad transmission symptoms of this problem include randomly overheat even where being used as stated.
How to Fix: Installing aftermarket transmission cooler possibly would resolve this problem, even though it points back to a defect in the original design. It is best to contact your local mechanic quickly to perform transmission troubleshooting before the problem worsens.
Transmission Control Indicator Lamp (TCIL)
The 2002 Ford Explorer models might also experience a problem with TCIL flashes for various DTC / diagnostic trouble codes when running a self-test. This transmission problem develops when water seeps through the body connector of the transmission solenoid.
How to Fix: For TCIL flashes, the transmission wiring harness should be replaced with an updated part by your local mechanic.
WHat is the Best Approach to Solving Ford Explorer Transmission Problems?
Method 1: Getting a Used Transmission for your Ford Explorer.
The fastest way to repair your 2002 Ford Explorer transmission problems is to purchase a used transmission. Used transmissions are usually on sale in most junkyards. They often come with warranties. The problem with this method is there is no way to determine its actual condition, and the warranty only covers the purchase, not the labor costs.
Method 2: Rebuilding your Ford Explorer Transmission
The rebuilding option for transmission requires a repair shop to remove your transmission and install several new parts during the process. The problem with this method is that it is highly dependent on the skills and experience of your transmission rebuilder. A warranty of 1 to 2 years may keep you covered at certain repair shops.
Method 3: Getting Remanufactured Ford Explorer Transmission
Several car owners are dependent on their vehicle to commute daily. Most gasoline engines are intended to go past 100’s of thousands of miles, so it is okay to invest a little more in getting a Remanufactured Ford Explorer Transmission.
Getting a basic understanding of your SUV’s transmissions is a bit of advice which works for everyone as it helps you save more regarding avoiding costly inspections and doing a simple task like changing transmission fluid.
It is imperative to care for your Ford Explorer by performing regular maintenance. Most transmission issues are known to start small. So quick detection is always the best. Transmission problems, repairs or replacements can be challenging, troublesome, and costly. Thus, the best advice remains to give special consideration to any car activities that seem uncommon.
Frequently Asked Questions About 2002 Ford Explorer Most Common Transmission Problems
Is it okay to drive a Ford Explorer with transmission problem?
Driving a car with transmission problems is not always a good option, and it is mainly dependent on the bad transmission symptoms. Continuous driving of a Ford Explorer with a transmission problem could result in more damages and expensive repairs.
How is transmission replaced in Ford Explorer?
Your Ford Explorer transmission is first lifted from the ground to gain access to all parts and for proper unbolting. After which the car is put down for a new transmission installation.
How often does Ford Explorer transmission need repairs/replacement?
Ford Explorer transmission repairs/replacement is mainly dependent on your maintenance level. On an average, between 80,000-180,000 miles. A high-quality transmission replacement can last longer if all flaws are correctly solved.
What is the best way to diagnose Ford Explorer transmission problems?
Using the right tools and experience from a certified mechanic/transmission repair center will be able to detect any diagnostic trouble codes (DTC’s). Once discovered, visual inspection can be performed to verify such problem.
2014 Ford Focus Most Common Transmission Problems and How to Fix Them
The 2014 Ford Focus is, at its best, a beautiful concept. Although they are still arguments over its competence, the Ford Focus shows some great strength in areas like customer service, economy, performance, reliability, and warranty. Although it drives rather smoothly like an automatic, the Ford Focus comes with a dual-clutch transmission. The dual-clutch transmission is a pretty neat theory.
2014 Ford Focus Transmission
It always begins with great joy in having your car back on the road. The Ford Focus comes with:
DPS6 Automatic Transmission.
Below are the most common 2014 ford focus Transmission Problems and possible fix to apply in getting your car back to life.
2014 Ford Focus Transmission Problems
Do you observe something wrong with your Ford Focus transmission? Below are some of the most Common Transmission Problems associated with the 2014 ford focus and How to Fix Them.
How to Fix Solenoid Problems on 2014 Ford Focus
Failure in solenoid is amongst the most common transmission problems faced by the Ford Focus model. The solenoid in Ford Focus is little like devices used by the car’s computer in changing gears and routing pressurized transmission fluid. The process of activating the solenoids in your car involves the car’s computer sends out active electric signals though wrapped wire coil carefully packed around the plunger device. Heating and vibration are the known bad transmission symptoms of Failure in Solenoid. Both symptoms cause these wires to short out, which leads to a variety of transmission problems.
How to Fix: To check your solenoids functionality, use an ohmmeter connected to the two wires from the solenoid. Readings of 20-30 ohms indicate proper functioning. Anything less or above may lead to your solenoid not to function correctly.
Transmission Clutch Shudder
The 2014 Ford Focus comes installed with Ford dual-clutch transmission (DPS6). Sometimes, distinct clutch shudders during transmission are experienced during little acceleration, whether there is fluid leakage surrounding the clutch housing or not. These transmission problems can be due to defective input shaft seals which permit the seeping of fluid and affect the clutch surface.
How to Fix: The input shaft seals require replacement. Also dependent on the level of damages experienced, another clutch assembly might become necessary. Nevertheless, there is a little possibility cleaning and reinstalling the clutch would solve this problem.
In line with the problem in the first case, if repairs are not correctly in place, it may lead to clutch contamination during repair. This issue could arise again since swelling and rupture may follow with new input shaft seals.
How to Fix: The accepted solution for this 2014 Ford Focus Transmission Problems is to apply brake cleaner in cleaning both the clutch assembly and bell housing. But, if there is no sufficient time for drying parts completely before installation, swelling and rupture could still be experienced with newer input shaft seals if they make contact with cleaning solvent.
Light Shudder During Shifts
After replacement of dual clutch assembly, it is not unusual to get a light shudder when shifting gears. These bad transmission symptoms are from the friction of clutch materials which needs a break in time of 1,000 miles.
How to Fix: Except there is noticeable fluid leakage, the clutch assembly would be needing no new replacement. In its place, ask your technician to reset the clutch travel by running the Adaptive Learning program from Service Routine Transmission on your Ford Focus.
Other Bad Transmission Symptoms
For other bad transmission symptoms that may come up with your 2014 Ford Focus, it is essential to detect and fix them. Some bad transmission symptoms may include delayed/ broken gear engagement, hard start, no crank/start, strange noise when starting your car, and several other diagnostic worry codes.
How to Fix: Before executing standard diagnostics, it is highly suggested to perform checks on the G-104 ground initially. This check is done to ensure enough body to ground connection is available. If you observe a loose eyelet, apply 12 Nm torque to the fastener. If no other issues are in sight, proceed with the standard diagnostic techniques.
Getting a basic understanding of your car’s transmissions is highly recommended as it aid getting a better knowledge of your vehicle as well as saving more regarding avoiding costly inspections and accomplishing a simple task like changing transmission fluid.
It is imperative to care for your Ford Focus with the steady maintenance schedule. Most transmission problems usually start small, so early detection are always the best. Transmission problems, repairs or replacements can be demanding, inconvenient, and typically cost. Thus, the best advice remains to pay special attention to any car activities that seem uncommon.
What is the Cost of Ford Focus Transmission Repairs?
In general, dependent on the make and model of your car, a remanufactured transmission would cost around $1,300 to $3,400. The labor cost to make such installation create an addition to the overall pricing of the unit. The labor cost usually runs from $400 to $800.
It is more expensive to perform transmission replacement than to have your transmission rebuilt.
Most Common FAQs for Ford Focus Transmission Repairs
Do you find it safe to drive a Ford Focus with transmission problem?
Usually, driving a car with transmission problems is not always recommended, as it is mainly dependent on the bad transmission symptoms you are experiencing at that moment. Having to drive of a Ford Focus with a transmission problem, can lead to more damages and costly repairs in the long run.
How is transmission replaced in Ford Focus?
Your Ford Focus transmission is first lifted from the ground to gain access to all parts and for proper unbolting. After which your car is placed low for a new transmission installation. Once the new transmission is in place, your vehicle needs to be reflashed/reprogrammed using updated GM subscription to accept this changes.
How often is repaired/replacement needed for Ford Focus transmission?
The Ford Focus transmission repairs/replacement is primarily reliant on your maintenance level and record. A recommendation from an average record is 80,000 to 180,000 miles. If you have a high-quality transmission replacement, they might turn out to last longer if all flaws get proper fixing.
What is the best approach to diagnosing my Ford Focus transmission problems?
Applying the right tools and experience from the right mechanic/transmission repair center will be able to detect any Diagnostic Trouble Codes (DTC’s). Once identified, visual inspection can be done to validate such glitches.
2002 Ford Explorer Transmission Problems / Transmission Repair in Charlotte NC
About the 2002 Ford Explorer:
The Ford Explorer is a full-size crossover SUV sold in North America and built by the Ford Motor Company since 1990, as a replacement for the smaller but related Ford Bronco II. It is manufactured in Louisville, Kentucky (it was also assembled in Hazelwood, Missouri until the plant closed on March 10, 2006). The Ford Explorer was instrumental in turning the SUV from a special-interest vehicle into one of the most popular vehicle types on the road.
The Ford Explorer has a huge problem with transmission failure, mostly from the early 2000s — especially the 2002–2004 Ford Explorer. Transmission problems in Ford Explorers are one of the most commonly complained about issues of any car on the road. One dealer even claims that 1 out of every 10 Explorer’s from the early 2000 model years will have transmission failure at some point.
What signs can you look for when it comes to transmission failure with the 2002 Ford Explorer? A common first time symptom is the blinking O/D light and noise, such as rattling or clanking, while shifting gears. If you are experiencing any of these transmission problems (trouble shifting, noises, O/D light is on), please contact us for a free diagnostic. Transmission problems only worsen with time. Sometimes, if the problem is not too severe, you can avoid a complete overhaul, but if you wait too long it may be your only option.
2002 Ford Explorer Transmission Problems
* Difficulty shifting gears
* Difficulty shifting into park
* Shifts into gear, but won’t go
* Makes a winding down noise when stopping
* Slips into neutral when stop
* Gears slipping
* Transmission fluid leaking
* Transmission Hesitates
* Loses gears
* Difficulty shifting from park into reverse
* Rattling noise from transmission
* Won’t shift into 3rd gear
* transmission slips when shifting and clunks
* O/D light is blinking
* clunking sound
Possible Solution to Transmission Problem Symptoms as listed above:
Some transmission repair shops will recommend replacing the solenoid pack. Solenoid pack will only repair certain conditions, such as delayed, harsh shifting into reverse and harsh shift from 1st to 2nd gear, and / or 740 torque converter code.
Although, a 740 code torque converter clutch can also be attributed to a hydraulic cross leak or or worn valves in the valve body, or a bad torque converter. Also, shift codes can be attributed from worn servo bores in the case. In that instance, this would call for the case to be fitted with new sleeves to repair the worn servo bores. This would be done in a complete transmission rebuild process.
To determine the exact solution for your transmission problem, you vehicle needs to be tested. We can properly scan your vehicle and do a hydraulic pressure test. This hydraulic pressure test will determine if you have an electrical, hydraulic or mechanical problem. Call us at 704-821-3460 to schedule this test.
Transmission Trouble Codes with the 2002 Ford Explorer:
DTC Codes – P0700-P0899 – Transmission
P0700 Transmission Control System Malfunction
P0701 Transmission Control System Range/Performance
P0702 Transmission Control System Electrical
P0703 Torque Converter/Brake Switch B Circuit Malfunction
P0704 Clutch Switch Input Circuit Malfunction
P0705 Transmission Range Sensor Circuit malfunction (PRNDL Input)
P0706 Transmission Range Sensor Circuit Range/Performance
P0707 Transmission Range Sensor Circuit Low Input
P0708 Transmission Range Sensor Circuit High Input
P0709 Transmission Range Sensor Circuit Intermittent
P0710 Transmission Fluid Temperature Sensor Circuit Malfunction
P0711 Transmission Fluid Temperature Sensor Circuit Range/Performance
P0712 Transmission Fluid Temperature Sensor Circuit Low Input
P0713 Transmission Fluid Temperature Sensor Circuit High Input
P0714 Transmission Fluid Temperature Sensor Circuit Intermittent
P0715 Input/Turbine Speed Sensor Circuit Malfunction
P0716 Input/Turbine Speed Sensor Circuit Range/Performance
P0717 Input/Turbine Speed Sensor Circuit No Signal
P0718 Input/Turbine Speed Sensor Circuit Intermittent
P0719 Torque Converter/Brake Switch B Circuit Low
P0720 Output Speed Sensor Circuit Malfunction
P0721 Output Speed Sensor Range/Performance
P0722 Output Speed Sensor No Signal
P0723 Output Speed Sensor Intermittent
P0724 Torque Converter/Brake Switch B Circuit High
P0725 Engine Speed input Circuit Malfunction
P0726 Engine Speed Input Circuit Range/Performance
P0727 Engine Speed Input Circuit No Signal
P0728 Engine Speed Input Circuit Intermittent
P0730 Incorrect Gear Ratio
P0731 Gear I Incorrect ratio
P0732 Gear 2 Incorrect ratio
P0733 Gear 3 Incorrect ratio
P0734 Gear 4 Incorrect ratio
P0735 Gear 5 Incorrect ratio
P0736 Reverse incorrect gear ratio
P0740 Torque Converter Clutch Circuit Malfunction
P0741 Torque Converter Clutch Circuit Performance or Stuck Off
P0742 Torque Converter Clutch Circuit Stock On
P0743 Torque Converter Clutch Circuit Electrical
P0744 Torque Converter Clutch Circuit Intermittent
P0745 Pressure Control Solenoid Malfunction
P0746 Pressure Control Solenoid Performance or Stuck Off
P0747 Pressure Control Solenoid Stuck On
P0748 Pressure Control Solenoid Electrical
P0749 Pressure Control Solenoid Intermittent
P0750 Shift Solenoid A Malfunction
P0751 Shift Solenoid A Performance or Stuck Off
P0752 Shift Solenoid A Stuck On
P0753 Shift Solenoid A Electrical
P0754 Shift Solenoid A Intermittent
P0755 Shift Solenoid B Malfunction
P0756 Shift Solenoid B Performance or Stock Off
P0757 Shift Solenoid B Stuck On
P0758 Shift Solenoid B Electrical
P0759 Shift Solenoid B Intermittent
P0760 Shift Solenoid C Malfunction
P0761 Shift Solenoid C Performance or Stuck Off
P0762 Shift Solenoid C Stuck On
P0763 Shift Solenoid C Electrical
P0764 Shift Solenoid C Intermittent
P0765 Shift Solenoid D Malfunction
P0766 Shift Solenoid D Performance or Stuck Off
P0767 Shift Solenoid D Stuck On
P0768 Shift Solenoid D Electrical
P0769 Shift Solenoid D Intermittent
P0770 Shift Solenoid E Malfunction
P0771 Shift Solenoid E Performance or Stuck Off
P0772 Shift Solenoid E Stuck On
P0773 Shift Solenoid E Electrical
P0774 Shift Solenoid E Intermittent
P0780 Shift Malfunction
P0781 1-2 Shift Malfunction
P0782 2-3 Shift Malfunction
P0783 3-4 Shift Malfunction
P0784 4-5 Shift Malfunction
P0785 Shift/Timing Solenoid Malfunction
P0786 Shift/Timing Solenoid Range/Performance
P0787 Shift/Timing Solenoid Low
P0788 Shift/Timing Solenoid High
P0789 Shift/Timing Solenoid Intermittent
P0790 Normal/Performance Switch Circuit Malfunction
P0801 Reverse Inhibit Control Circuit Malfunction
P0803 1-4 Upshift (Skip Shift) Solenoid Control Circuit Malfunction P0804 1-4 Upshift (Skip Shift) Lamp Control Circuit Malfunction
2002 Ford Explorer Transmission Fluid Flush / Check
Sometimes Transmission problems can be the result of a transmission not be serviced on time. If the transmission fluids have not been changed or if the fluids are low, this can very quickly cause a problem in any vehicle’s transmission. The 2002 Ford Explorer does not come with a dipstick to check the transmission fluid, but there are ways to still do so. Ford did come out with a special tool needed for servicing the transmission fluids, which can be purchased, but it isn’t commonly found. If you are in need of a transmission fluid flush for your 2002 Ford Explorer, please contact us at 704-821-3460 to schedule an appointment.
For a Free Diagnostic on your 2002 Ford Explorer transmission problem, please call us at 704-821-3460, stop by in person or email us at firstname.lastname@example.org We have over 30 years experience with Ford Transmissions (and all other types of Transmissions). Ford won’t move or don’t want to drive? Free Towing is available with all transmission rebuilds (mileage restriction may apply).